INSTRUCTION MANUAL
Solar Power Vibration/Magnet Alarm - MH206
Introduction
MH206 built in rechargeable lithium battery for power,also with solar panel to provide enough current for standby using under the normal illumination. and help extend using life of the lithium batteries .With both vibration and magnet function .
Product Image
Accessories:
Check and identify the contents of your package :
Alarm Installation
Place the alarm in the desired location, preferably on door or window with screws or adhesive tape supplied.
Magnetic contact
The magnetic contact must be installed at the closet distance to the alarm so that contact can be made when door or window is closed, either on the left or right hand side. Gap between magnet and alarm should be within 10mm.
Note: Red LED is on to indicat the battery is in no power ,simply using the mobile mirco usb cable to charge the power .
Security code setting
1,Under disarm mode ,input default code(default factory code '1234'), LED starts flashing for 30 seconds,
2, Enter new four digits security code,
3, Red LED light stop flashing to confirm new code is set successfully and turn to disarm mode.
NOTE: The first digit of new code can't be '4', and the former three digits can not be set as '111' or '222'. Such digit codes will be forbidden and turn to disarm mode.For security reason, if this procedure is not completed correctly within 30 seconds, alarm will return to disarm mode.
Activate/deactivate vibration function
Under disarm mode, input correct code, then input activate code '222', red LED will flash three times to confirm the vibration function is activated and return to disarm mode.
Under disarm mode, input correct code, then input deactivate code '111', red LED will flash three times to confirm vibration function is deactivated and return to disarm mode.
NOTE:The vibration detect function is activated automatically when batteries are installed properly each time.
When existing from the protected area
Press number '4' on keypad and a confirmed tone will indicate that the alarm is armed. You have 30 seconds to vacate the area. After this time, if magnetic contact is broken or vibration is detected, the alarm will be triggered.
When entering the protected area
Simply type your four digit security code(default factory code '1234') within 5 seconds. This will disarm the alarm.
Solar Power Vibration/Magnet Alarm - MH206
Introduction
MH206 built in rechargeable lithium battery for power,also with solar panel to provide enough current for standby using under the normal illumination. and help extend using life of the lithium batteries .With both vibration and magnet function .
Product Image
Accessories:
Check and identify the contents of your package :
- 1 x Main unit
- 1 x Fixing screws to secure main unit to the wall
- 1 x Fixing screw to secure back cover
- 1 x 3M tape
- User manual
Alarm Installation
Place the alarm in the desired location, preferably on door or window with screws or adhesive tape supplied.
Magnetic contact
The magnetic contact must be installed at the closet distance to the alarm so that contact can be made when door or window is closed, either on the left or right hand side. Gap between magnet and alarm should be within 10mm.
Note: Red LED is on to indicat the battery is in no power ,simply using the mobile mirco usb cable to charge the power .
Security code setting
1,Under disarm mode ,input default code(default factory code '1234'), LED starts flashing for 30 seconds,
2, Enter new four digits security code,
3, Red LED light stop flashing to confirm new code is set successfully and turn to disarm mode.
NOTE: The first digit of new code can't be '4', and the former three digits can not be set as '111' or '222'. Such digit codes will be forbidden and turn to disarm mode.For security reason, if this procedure is not completed correctly within 30 seconds, alarm will return to disarm mode.
Activate/deactivate vibration function
Under disarm mode, input correct code, then input activate code '222', red LED will flash three times to confirm the vibration function is activated and return to disarm mode.
Under disarm mode, input correct code, then input deactivate code '111', red LED will flash three times to confirm vibration function is deactivated and return to disarm mode.
NOTE:The vibration detect function is activated automatically when batteries are installed properly each time.
When existing from the protected area
Press number '4' on keypad and a confirmed tone will indicate that the alarm is armed. You have 30 seconds to vacate the area. After this time, if magnetic contact is broken or vibration is detected, the alarm will be triggered.
When entering the protected area
Simply type your four digit security code(default factory code '1234') within 5 seconds. This will disarm the alarm.